This should only be seen by the programmer when testing from his IP address.
If you see this message please contact the programmer.
The programmer is excluded from the hit counter because this is a local IP=44.200.40.195. posBot=
EULAFlag =
Please accept the use of cookies for Google Advertising.
The EULA (end-user license agreement) is shown below, near the end of the menu buttons. The main source of income from this site is through advertising and the program will not run unless you agree to accept advertising. RideTheGearTrain does not use cookies or any personal information, but Google Advertising does. Details are given in the EULA below and this includes instructions for controlling Google.
Yes, I accept the use of cookies and advertising.
No, don't run RideTheGearTrain
OPTIONAL ENTRIES
Optional
Entries
Maximum number of results to display.
Max
Results
How many results do you want to read?
eg 100, 500, 2000
Gear ratio of longitudinal power feed
Carriagefeed
Ratio
Power feed along the length of the bed as a fraction of thread pitch, often about one third. (Longitudinal feed, sometimes known as sliding).
Gear ratio of cross-slide power feed
Crossfeed
Ratio
Cross-slide power feed as a fraction of thread pitch
(Used for 'facing' or 'surfacing'. Usually about 0.1)
Changeable Stud Gear or Spindle Gear?
Changeable
Stud
Can the stud or spindle gear be removed and changed? Some Asian lathes have the stud gear machined as part of the spindle shaft, so that it cannot be changed. This is the first gear in the gear train.
Yes
The first gear in the train, or "stud gear", CAN be changed.
It is assumed that the plain change gears are used here. South Bend clones such as the Boxford A, B, C use this system.
No
The first gear in the train cannot be changed. Enter the number of teeth below:
How many teeth are on the first gear in the train ?
Boxford and most other lathes allow you to change it. Often Chinese mini-lathes do not allow it to be changed and do not mention it in their gear charts. Most mini-lathes have 40 teeth machined into the spindle. If it cannot be changed, enter the size of the first gear in the chain here. This may be the stud gear or a gear machined into the spindle shaft (which has the chuck mounted on the other end).
Changeable gear on the leadscrew or gearbox?
Changeable
LSG
Can the leadscrew gear be removed and changed?
On some lathes the last gear in the train cannot be changed. This gear is mounted on the lead screw or gearbox input and is referred to as the "Leadscrew Gear (LSG). It is assumed that the plain change gears are used. They can be changed on South Bend clones such as Boxford lathes.
Yes
The leadscrew gear, CAN be changed.
eg South Bend / Boxford and most other lathes allow you to change it
No
The leadscrew gear CANNOT be changed.
How many teeth are on the leadscrew gear?
Only required if the gear is not changeable.
Change the lead-screw pitch or TPI
Leadscrew
Enter leadscrew pitch in mm or TPI.
The leadscrew pitch has been set as part of the lathe specifications eg South Bend 9" clone metric lathes have a 3mm leadscrew, while imperial lathes have 8 Threads Per Inch, unless changed here.
ADVANCED MODIFICATIONS
Does the lathe have a lead-screw gearbox for cutting threads?
Gearbox
Fitted
Yes, it has a gearbox
No gearbox fitted
Is the lead-screw imperial or metric?
Lathe
Type
If the lead-screw is metric the lathe is defined as a metric lathe.
Metric Lead-screw (mm pitch)
Imperial Lead-screw (TPI)
Primary Ratio of the gearbox
Primary
Ratio
Alter the primary ratio
If your gearbox is similar to one of the gearboxes provided in the list, but the standard gears are different you can adjust the primary ratio of the gearbox here.
Click the help button (?) and then 'Return...' for a detailed explanation.
Fudge Factor
Fudge
Factor
Enter a Fudge Factor
This is normally blank. A few rare and unusual lathes may need to have the calculated pitch or TPI adjusted by multiplying the primary ratio by a 'Fudge Factor'.
Click the help button (?) for a detailed explanation.